Go Back   tbirdforum.com > Thunderbird Model Years > Early Birds [1955-1957]

Early Birds [1955-1957] Have a Super Sharp 1955 to 1957 Thunderbird or just want to learn about them? Show yours off and talk about them here.

'56 Rear spring setting

This is a discussion on '56 Rear spring setting within the Early Birds [1955-1957] forums, part of the Thunderbird Model Years category; Does anyone know the correct setting of the rear leaf springs on a '56? If they were, say, standing up-side-down ...

Reply
 
LinkBack Thread Tools
  #1 (permalink)   IP: 121.72.54.185
Old 08-12-2014, 05:47 PM
 
Join Date: Jul 2014
Posts: 15
Rep Power: 0
peter1956 is on a distinguished road
'56 Rear spring setting

Does anyone know the correct setting of the rear leaf springs on a '56? If they were, say, standing up-side-down on the ground, what should their height measurement be?
Reply With Quote
  #2 (permalink)   IP: 70.160.98.203
Old 08-12-2014, 06:54 PM
Jimz Bird's Avatar  
Join Date: Feb 2011
Location: Norfolk, VA
Age: 76
Posts: 53
Rep Power: 19
Jimz Bird is on a distinguished road
Hi again Peter,

Here ya go. Just off the top of my head.
These are assembled spring dimensions.
Width = 2"
Distance between mouning bolt holes on ends = 25 1/4" (one end to center), 30" (center to other end) = 55 1/4" total
Arch - Straight line between holes to top of assembled springs = 7 3/4"
Assembled thickness of all 5 leaves = 1 5/16"

I have also attached a graphic of the spring.

If you have the CASCO catalog (print or .pdf) page 20 has all the parts you need to rebuild them. Including the anti-squeak pads. Other vendors have them also.
There is a difference in the spring clamps. The older style (55/56) has rubber on the top also and the newer (56/57) style has rubber only on the bottom and sides.

OK, not quite off the top of my head. It was something I had wondered about in the past so I dug around and found the info here.
1956-1957 Ford Thunderbird - Leaf Spring (Rear - 5 Leaves) - 42-211 | $138.95

The info on the clamps is from the CTCI Restoration Manual.
If you do need to replace them I would check to see where they are made. These are less expensive than CASCO, but if they are Chinese junk steel I would "spring" for the USA steel made ones regardless of price.
There are other spring vendors also.

Let us know what you come up with and what you do.

Hope this helps.

Jim
__________________
"MABLE"
1956 Thunderbird Green / Brown Interior (ZE-XG)

http://www.squarebirds.org/users/Jim...ite/index.html

Last edited by Jimz Bird; 04-08-2015 at 07:38 PM.
Reply With Quote
  #3 (permalink)   IP: 68.35.141.0
Old 09-16-2014, 02:36 PM
 
Join Date: Jul 2012
Posts: 29
Rep Power: 0
Rusty1 is on a distinguished road
'56 rear spring setting

peter1956,
In lew of getting "NEW" springs, if yours are not up to snuff you might try a local spring and suspension shop. They may be able to re-arch yours. It is a lot cheaper and depending on how much you drive the car will last quite a long time. Good luck...
Rusty1
Reply With Quote
  #4 (permalink)   IP: 125.237.147.88
Old 09-17-2014, 04:50 AM
 
Join Date: Jul 2014
Posts: 15
Rep Power: 0
peter1956 is on a distinguished road
Suspension low

My ’56’s suspension was sitting a bit low in the rear and noticeably lower on the left side. I fitted new top and bottom inner suspension bushes. Also 2 new coils. I also removed and dismantled the rear springs. I cleaned up the leaves, and put a bit more set in them. (re-arched them). The left one was less, but both are now equal. I also renewed all bushes, shackles, insulator pads, etc. All back together, the ride height is much better, but still sits lower on the left.
NOW! There was a spacer on the left coil. I assumed this was to counteract a weak spring, so didn’t put it back. I read somewhere that these were also put in to compensate for extra weight on the left, eg, A/C. I don’t have A/C.
Has anyone else battled with this scenario?
Reply With Quote
  #5 (permalink)   IP: 68.35.141.0
Old 09-17-2014, 09:32 AM
 
Join Date: Jul 2012
Posts: 29
Rep Power: 0
Rusty1 is on a distinguished road
56 spring setting

peter1956,
The spacer in the front coil is there for two reasons. One is compensate for the road crown and two it is there to compensate for driver weight. These cars were mostly one person cars. You should put it back. Sounds like you have done all the corrective measures to the rears. Maybe the front coils are also sagging. ??
Rusty1
Reply With Quote
  #6 (permalink)   IP: 70.160.98.203
Old 09-17-2014, 10:29 AM
Jimz Bird's Avatar  
Join Date: Feb 2011
Location: Norfolk, VA
Age: 76
Posts: 53
Rep Power: 19
Jimz Bird is on a distinguished road
Peter,

Yes, as Rusty stated it is on the left only.
The Restoration Manual speaks of it as well as the vendors sell it for the left side only.
It is also listed in the Ford Parts Catalog as 5355 (55-57 S LH only) The "S" is of course Thunderbird.
Other than that it sounds like you did well on the rebuild.

Jim
Attached Images
File Type: jpg 5355 Shim Front Spring..jpg (16.9 KB, 17 views)
__________________
"MABLE"
1956 Thunderbird Green / Brown Interior (ZE-XG)

http://www.squarebirds.org/users/Jim...ite/index.html
Reply With Quote
  #7 (permalink)   IP: 121.72.54.185
Old 09-17-2014, 09:17 PM
 
Join Date: Jul 2014
Posts: 15
Rep Power: 0
peter1956 is on a distinguished road
Yes, I think I will put it back. I did put brand new coils in the front. As far as the rear is concerned, I may have to put a spacer between the spring and axle on the right side to lower it. Also will try leaving the insulator rubber out on the left side, which will raise it a bit.
Reply With Quote
  #8 (permalink)   IP: 68.35.141.0
Old 09-18-2014, 09:01 PM
 
Join Date: Jul 2012
Posts: 29
Rep Power: 0
Rusty1 is on a distinguished road
peter1956

Those things may solve the problem but when you get a bump squeak you'll know where it is coming from. The insulator is an anti-squeak item.
Rusty1
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -4. The time now is 06:27 AM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.0
Garage vBulletin Plugins by Drive Thru Online, Inc.